SWITCHBOARD
Easy-tronic features
The EASY-TRONIC modular system enabled our designers to develop a framework (system) innovative and reliable microprocessor.
This system allows delegation to peripheral coprocessors the task of activating the respective inputs and outputs; in this application each node of the system is connected with a simple two-wire cable. The serial communication system which is used between the cabin cards and the control panel is based on the CAN (Controller area network). The Protocol follows the rules ISO 11898-1 for low speed transmissions (up to 125 kbit/sec), high level of immunity to noise and to cover longer distances (up to 500m).
The configuration CAN is multi master. In other words the unit that needs to send information takes possession of the bus signal and sends its information which is received and decoded by the receiving units. If more than one unit takes over the bus automatically the priority message is assigned. If a check produces a negative result the message will be repeated.
Features
-
EASY-Q: motherboard of the switchboard. This is the basis of the system, it supports the following peripheral devices:
-
EASY-D: user interface card and programming unit of the switchboard
-
EASY-DR: Remote user interface card and switchboard programming unit.
-
EASY-X: Interface tab towards plan-only calls in parallel mode
-
EASY-P: interface card towards plan-only calls in SERIAL mode
-
EASY-EEP: data memory reassembled’s lift, where all parameters are stored
-
EASY-S: circuit control board safety circuit
-
MONITEC: system remote management card (optional)
-
GSM500: system remote management card (optional)
-
SINTEC: voice synthesis card in lift cabin (optional)
-
EASY-C: Cabin roof board; processes all communications between cabin and switchboard and supports:
-
EASY-X: interface card for cabin calls (installations with more than 8 stops)
-
EASY-L13: battery charge card and alarm management
-
-
- base 8 stops (universal or collective descent)
- extension up to 64 stops (128 services)
- unlimited underground floors
- user interface:
- programming of installation parameters
- special functions:
- inspection
- doors control
- called inclusion
- error diagnostics and recording
- setting date and time
- hydraulic elevator:
- control units: all
- direct starting
- star or triangle starter
- soft starter
- rope elevator:
- 1 speed
- 2 speed
- V3F open loop (until 1 m/s)
- V3F closed loop (until 4 m/s)
- universal maneuver
- collective descent
- collective up/down
- maneuver un/coll
- multiplex (unti 4 elevator)
- overload and full load
- priority of cabin
- priority call to floors
- call fire
- maneuver firemen
- out of service
- interfloor low
- device for emergency manoeuvre
- vocal synthesis
- remote monitoring
- automatic, semi-automatic and manual
- single, double or triple access
- simultaneous or selective opening
- parking at closed or open doors
- type of operators: all
all inputs and outputs are protected against:
- over-voltage (until 125 Vcc)
- short circuit (on the 24 Vcc)
- electromagnetic interference (according to standart EN)
- main voltage
- standard: triphase 380V, 400V-50HZ
- optionals: triphase 208V, 220V, 415V
- monophasic 220V
- brake or valve voltage
- standard 48/60 vdc
- optionals: all
- circuit voltage safety
- standard: 48/60 vdc
- optional: 110 vac
- 24 VDC MAX 1,5 W
- busy/coming
- available
- cabin call recording
- recording floor calls
- direction of cabin
- next departure
- position indicator: 7 segments
- 1 pole for floor, track
- overload
- out of service
- fire/fireman
- protection engine temperature
- thermal engine
- oil pressure
- oil temperature
- missing/reversal phase
- time max run
- overload-full-load
- parking on the selected floor
- light cabin off
- law 13 DM 236
- emergency light cabin
control of inputs and outputs of all components (es.: photocell, mobile rib, door opening button ecc.)
- bistable, monostable magnetic sensors
- encoder (suggested line drive 1024 ppr)
- floor restoration and door opening (rope and hydraulic)
- telephone dialer
- EN 81-1
- EN 81-2
- 95/16/CE
- EN 81-28
- EN 81-70
- LAW 13 DM 236
- the SYSTEM-LIFT control panel meets the requirements for the mark CE in accordance with Directive 89/339/EEC and on next 93/68/EEC
- EN 50081-1 electromagnetic emissions
- EN 50082-2 electromagnetic immunity
- certificate of conformity N.0072/02
